Drawing scale

Calibrate each sheet so measurements are accurate.

Before measuring, set the drawing scale so Vellum can convert on-screen distances into real-world dimensions. Every sheet has its own scale.

Setting the scale

  • Click the scale control in the bottom bar. It shows the scale of the sheet on screen, then the unit its measurements read in. The top of its menu repeats the sheet's scale and where it came from.
  • Choose Apply to: This sheet (the default), All sheets, or Pages… with a list like 1-3, 5.
  • Choose a standard scale such as 1" = 10' or 1/4" = 1'-0", or a metric one such as 1:100.
  • Or Calibrate from drawing…: click two points of a known distance and type it. Custom scale… takes an equation for a non-standard ratio.

Scales read from the sheet

When a sheet has no scale yet, Vellum reads the one printed on it, such as 1" = 10' beside the title block's scale bar or SCALE: 1/4" = 1'-0", and its menu says Detected from sheet. Small insets such as vicinity maps are skipped, and NTS means no scale. A scale you set is never replaced. A sheet with no scale stays at full size, 1" = 1", in grey; its menu says Not set. Hover the scale control to see where a sheet's scale came from.

After your first measurement on a sheet that is still Not set, a prompt by the scale says Scale not set. Calibrate or pick a scale., with Calibrate and Pick a scale buttons. It shows once and goes away on its own.

Viewports: details and profiles at their own scale

A sheet often holds drawings at different scales: a detail at 1" = 2' on a plan at 1" = 20'. Give that part of the sheet its own scale with a viewport: a rectangle with a name and a scale. Measurements that start inside it (their first point) use its scale; everything else uses the sheet's.

  • Open the scale control and choose Add viewport…, then drag a rectangle around the detail or profile.
  • Name it, and pick its scale, or Calibrate… or Custom… for it (they apply to This viewport). Choose Create viewport.
  • The scale control lists the sheet's viewports. Click one to rename, rescale, resize (drag a corner, or drag a new rectangle) or delete it.
  • A small badge at the front of the scale control shows the number of the viewport under the cursor, with the viewport's scale beside it. The number is the one its name ends with (Detail 3 shows 3), or else its place in the sheet's list. Off a viewport the badge is an empty frame, so the bar never shifts as you move. Open the menu over a viewport and it applies to This viewport.
  • Viewports show as dashed outlines with a name and scale tag while the Dimension or Area tool is active. They are setup, not markup: they never print or export.
  • A measurement made in a viewport keeps it: another viewport drawn or resized over it never changes its numbers. A measurement outside every viewport reads the sheet's scale, or that of a viewport you later draw around it (the way to fix a detail measured before its viewport existed). Moving or reshaping a measurement measures it again where it lands.

Profiles: separate horizontal and vertical scales

A profile draws its vertical at a larger scale than its horizontal (1" = 20' horizontal, 1" = 2' vertical). Give its viewport a Vertical scale; when the sheet notes one, it is offered when you draw the viewport. A dimension there reads H 120.00 ft · V +4.20 ft · +3.50%: the horizontal distance, the rise from left to right, and the grade (rise over run). In Properties, Profile › True length shows the length along the line instead, from both scales. Areas there read horizontal × vertical. Dimensions in a profile show no bearing: its angles are exaggerated.

Measure accuracy depends on scale

If the scale is wrong, every length and area will be wrong. Confirm the scale against a known dimension on the sheet before relying on measurements.

Once set, the Dimension tool and Area tool report real-world values in the scale's unit (feet, meters, or inches at full size). On an architectural scale such as 1/4" = 1'-0", lengths read in feet and inches, such as 15'-1 5/8". Calibrating or picking a scale sets units back to Match drawing scale. Configure units, format and rounding in Units & precision.